Come in the Clutch (Replacing a Clutch)
Does the motorcycle feel like it is slipping? Are there loud noises coming from the primary? These conditions generally point towards an issue with the clutch or compensator drive. These problems can be fixed sometimes with a simple adjustment. The clutch cable can have so much slack the clutch is chattering every time the engine is running. A lack of lubricant can also cause overheating and wear problems in the clutch. The first step is to inspect.
On some motorcycle models an inspection cover can be removed to see the condition of the clutch and primary chain. This would be an excellent place to start. Some motorcycles use a derby cover to inspect the clutch and adjust it, others adjust from the side of the engine. In order to remove and inspect a clutch, it usually will need to be completely unadjusted and loosened.
Clutches on motorcycles work with plates in a basket. The basket holds the clutch plates and friction discs. There are usually springs and pushrods to make all this work. When an engine is running and the clutch handle is squeezed, the spring(s) is/are compressed and the discs and friction plates slip past each other. This causes the engine to spin freely of the transmission so that there is no connection between the two. However, the friction plates lose their grip and springs can sag over time. This is the time when a clutch overhaul is needed.
Accessing the clutch can require some engine disassembly. First drain the clutch lubricant. A drain plug under the clutch is usually how this is done. On some bikes the oiling system is connected, so you will have to drain the motorcycle’s oil. On a sport bike type motorcycle, the clutch has a cover that is usually retained with a few bolts. Once they are removed, the cover should come off with ease. On a cruiser type motorcycle, the clutch is located within a primary case. Again it is held with perimeter bolts and removed from the side of the engine. The clutch will be exposed once the cover is removed.
This site and articles contained herein are provided for general informational purposes only and are not a substitute or intended as professional advice. Please be sure to refer to your owner’s manual or consult a mechanic for information specific to your motorcycle. The information contained on this site and articles contained herein are provided on an “as is” basis with no guarantees of completeness, accuracy, usefulness or timeliness and without any warranties of any kind whatsoever, express or implied. Rider Insurance Company, Rider Insurance Agency, Inc. and its affiliates (together, “Rider”) assume no responsibility for any errors or omissions in the content of this site and articles contained herein. Any action taken upon this information is strictly at your own risk and Rider will not be liable for any losses or damages in connection with your use of this site and articles. Additional terms and conditions apply and are available at https://model.rider.com/plymouth-rock-assurance-general-terms-and-conditions/.
Clutch replacement usually means you are changing the friction discs, metal plates, springs and maybe a stretched cable. A nut holds a spring which is on a stud that holds all of the discs and plates in place. A special tool is usually required to depress the clutch springs so that the nuts that hold them on can be loosened and removed. This tool can sometimes just be made with a piece of flat stock steel drilled across two spring studs that hold the clutch down. The nuts can be removed and the springs taken off. The plates will slide out and new plates can be reinstalled. Some require pre-lube before installation.
Once the plates are in place, the springs will need to be depressed with the special tool and nuts reinstalled with lock washers or thread locker. Torque to manufacturer specifications. Make sure no springs are binding and that everything seems to be moving freely. A new clutch cable may need to be installed as well. These are usually attached to a clutch releasing mechanism. It can be spring loaded. An adjuster on the cable should give enough slack to slide the cable end from the handle bar lever. It can then be removed from the engine side as well. Reinstall in the reverse order. Lube the clutch cable with cable lubricant. If the motorcycle uses a hydraulic mechanism, no replacement should be necessary.
Once the clutch is installed and inspected the clutch cover or primary case can be reinstalled. A new gasket may need to be installed if the system is enclosed in oil. The perimeter bolts should be torqued to manufacturer specifications and lubrication should be added if necessary. The clutch cable can be adjusted. The motorcycle should be tested at low speeds to make sure the clutch is fully engaging and disengaging. Once broken in, it should provide a smooth and torquey ride.
Plymouth Rock Assurance is a marketing name used by a group of separate companies that write and manage property and casualty insurance in multiple states. Motorcycle insurance in New Jersey and Pennsylvania is underwritten by Rider Insurance Company. Each company is financially responsible only for its own insurance products. Actual coverage is subject to the language of the policies as issued by each separate company.
